ZCUT3 Parts List Part # Description ZCUT3-A01A front panel 60mm ZCUT3-A01B front panel 80mm ZCUT3-A01C front panel 150mm ZCUT3-A01D front panel 250mm ZCUT3-A02A case 60mm ZCUT3-A02B case 80mm ZCUT3-A02C case 150mm ZCUT3-A02D case 250mm ZCUT3-A03A bottom case 60mm ZCUT3-A03B bottom case 80mm ZCUT3-A03C bottom case 150mm ZCUT3-A03D bottom case 250mm ZCUT3-A04 switch board 60mm ZCUT3-A05 […]
TDA025 Parts List Part # Description TDA025-01 turn table TDA025-02 start switch TDA025-03 ratchet set TDA025-05 slit plate TDA025-06 spring TDA025-07 micro switch lever TDA025-08 micro switch, spring (l) TDA025-09 micro switch, spring (s) TDA025-10 screw TDA025-11 body TDA025-12 micro switch TDA025-13 nameplate (on turntable) TDA025-14 safety cover TDA025-15/16 tape holder TDA025-17 switch cover TDA025-18 […]
TDH205 Troubleshooting Guide Not Cutting: Check and clean blades, replace if dull Check for worn or broken lower blade spring Check lower blade adjustment Not Feeding: Check yoke spring adjustment Check feed gear assembly for missing or flattened teeth Check for missing feed handle pawls Check blades for accumulated grease or tape resins […]
zcM1000 Series – “ERR” Message Turn unit off. Turn photo sensor switch off Turn unit on. Display should read 20. Press Feed button. If “ERR” appears, bad feed motor or circuit board. Press Cut button. If “ERR” appears, bad cutter motor or circuit board. To determine if it is a motor or driver, switch the […]
zcM1000P504 Replacement Instructions Remove 4 each P233 screws and 1 each P106 knob, then lift cover from tape dispenser. Unplug connectors from P111 transformer, P187 cut motor, P435 feed motor and P200 cut head inlet. Unscrew 3 each P232 screws and 1 each P239 screw that mount board to machine. Remove board by tilting it […]
zcM1000P680 Installation Instructions Remove cutting head from tape dispenser Place finger guard on cutting head so that it sits flat on the outer part of the cutting head and straddles the inner part of the cutting head. Align the guard so that the top of the guard is even with the top of the inner […]
zcM1000 Cutting Head Connector Replacement Removing Old Connector: Remove Cutting Head and Pressure Knob from machine Remove 4 of each Screw from Cover and lift Cover off machine. Locate P200 Connector and unplug from Main Board. Remove Connector by unscrewing nut on inside of Cover and pulling Connector out through front on machine. […]
Sensor Replacement – LD7500 Remove brown wire from relay Cut blue wire close to the gray sleeve, far from the connector. Loosen 2 black round screws and nut plate that hold sensor to bracket and remove the sensor Using screws and nut plate, mount new sensor. Run new sensor wire in the same place as […]
ZCUT3060 Recommended Spare Parts Quantity Part Number Description Price Each 1 ZCUT3-E04A Silicone Roller $46.40 1 ZCUT3-C05 Drive Gear – 18 Teeth $26.10 1 ZCUT3-C06 Drive Gear – 10 Teeth $20.30 1 ZCUT3-C12 Drive Chain-Short $11.50 1 ZCUT3-C13 Drive Chain-Long $13.10 1 ZCUT3-E19 Spring-Pressure Roller $6.60 2 ZCUT3-E20 Spring-Blade Tension $3.80 1 […]
ZCUT3 Series Recommended Spare Parts Quantity Part Number Description 1 ZCUT3-E04 (A-D) Silicone Roller 1 ZCUT3-C05 Drive Gear – 18 Teeth 1 ZCUT3-C06 Drive Gear – 10 Teeth 1 ZCUT3-C12 Drive Chain-Short 1 ZCUT3-C13 Drive Chain-Long 1 ZCUT3-E19 Spring-Pressure Roller 2 ZCUT3-E20 Spring-Blade Tension 1 ZCUT3-E22 Blade – Pkg of 5 Preventive Maintenance Weekly: […]